Philips customers using or selling these products for datasheet search, datasheets, Datasheet A82C Datasheet(PDF) 19 Page – NXP Semiconductors. A82C CAN Controller Interface. Product specification Supersedes data of Oct 21 File under Integrated Circuits, IC18 Jan FEATURES Fully. DATA SHEET. Product specification. Supersedes data of Oct File under Integrated Circuits, IC Jan INTEGRATED CIRCUITS. PCA82C
|Published (Last):||23 September 2006|
|PDF File Size:||2.76 Mb|
|ePub File Size:||15.15 Mb|
|Price:||Free* [*Free Regsitration Required]|
If a HIGH level is applied to pin 8, the circuit enters a low current standby mode. Stress above one or more of the limiting values may cause permanent damage to the device. For lower speeds or shorter bus length, an unshielded twisted pair or a parallel pair of wires can be used for the bus. For high-speed operation, the transmitter output transistors are simply switched on and off as fast as possible. In this mode, no ratasheet are taken to limit the. In this mode, the transmitter is.
If there are data sheet limits not guaranteed, these will datahseet separately. The rise and fall slope can be programmed with a resistor connected from pin 8 to ground.
The slope is proportional to the current output at pin 8. A current limiting circuit protects the transmitter output.
These products are not designed for use in life support appliances, devices, or systems where malfunction of these. A current limiting circuit protects the transmitter output stage against short-circuit to positive and negative battery voltage.
A82C250 Datasheet PDF
Electronic Components Datasheet Search. These are stress ratings only and operation. It is primarily intended for high-speed applications up to 1 Mbaud in cars. Pin 8 Rs allows three different modes of operation to be. All other parts of the IC will remain.
The rise and fall slope can be programmed with a. Semiconductors assumes no liability for device functionality or performance of the die or systems after third party sawing. The thermal protection is particularly needed when a bus line is short-circuited.
Part Name Included start with end match. To reduce RFI, the rise and fall slope should be limited.
All die are tested and are guaranteed to comply with all data sheet limits up to the point of wafer sawing for a period of. It is the responsibility of the customer to test and qualify their application in.
A82C250 PDF Datasheet浏览和下载
The thermal protection is particularly needed. The device provides differential transmit capability to the bus and differential receive capability to the CAN controller. All other parts of the IC will remain in operation. Accordingly, Philips Semiconductors assumes no liability for device functionality or performance of the die datashwet systems after third party sawing, handling, packing or assembly dqtasheet the die. The device provides differential transmit capability to. There are no post packing tests performed on individual die or wafer.
Use of a shielded cable is recommended to avoid RFI problems.
A82C Philips Semiconductors, A82C Datasheet
Because the receiver is slow in standby mode, the. Because the receiver is slow in standby mode, the first message will be lost. Because the transmitter is responsible for the major part of the power dissipation, this will result in a reduced power dissipation and hence a lower chip temperature. If a HIGH level is applied to pin 8, the circuit enters a low.
A82C datasheet(4/20 Pages) PHILIPS | CAN controller interface
Philips customers using or selling these products for use in such applications do so a82c2250 their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. Exposure to limiting values for extended periods may affect device reliability. Philips customers using or selling these products for.
The high-speed mode is selected by connecting a82c20 8 to ground. If dominant bits are detected differential bus voltage.
If there are data sheet limits not guaranteed, these will be separately indicated in the data sheet. Pin 8 Rs allows three different modes of dqtasheet to be selected: Stress above one or. The microcontroller should react to this condition by switching the transceiver back to normal operation via pin 8. Although the power dissipation is increased during this fault condition, this feature will prevent destruction adtasheet the transmitter output stage.
Philips Semiconductors has no control of third party procedures in the sawing, handling, packing or assembly of the die. Electronic Components Datasheet Search. In this mode, the transmitter is switched off and the receiver is switched to a low current.
This data sheet contains preliminary data; supplementary data may be published later. Part Name Included start with end match.