Buy ASTM D CLASSIFICATION FOR MACHINE-MADE ‘ FIBERGLASS’ (GLASS-FIBER-REINFORCED THERMOSETTING-RESIN) PIPE from SAI. Find the most up-to-date version of ASTM D at Engineering This classification covers machine-made “fiberglass” (glass-fiber-reinforced thermosetting-resin) pressure pipe. Methods of classification.
|Published (Last):||14 September 2007|
|PDF File Size:||19.83 Mb|
|ePub File Size:||7.27 Mb|
|Price:||Free* [*Free Regsitration Required]|
Methods of classification, requirements, test methods and the method of marking are included. This standard does not purport to address all of the safety concerns, if any, associated with its use. A The cell-type format provides the means of identification and specification of piping materials.
Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters.
Each part is one ‘designation order’ i. It covers the following types, grades, and classes of machine-made?
This standard is being withdrawn without replacement due to its limited use by industry. Note 2 — There is no known ISO equivalent to this standard. For the second generator, the property must be supplied by the FRP fiberglass pipe manufacturer in order to generate the ASTM D designation code for the piping.
Our webmaster is too poor to buy the latest version D ; therefore, this designation code generator is based on ASTM D data which is probably what many manufactures use. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Description of Terms Speci? Table 1 data was divided into 4 Parts for spacing considerations.
The values in parentheses are provided aztm information only. NOTE 1—For the purposes of this standard, polymer does not aastm natural polymers.
The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Table 1 presents a summary of the designation requirements. The outside diameter of the?
The values in parentheses are provided for information only.
It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Stay on Page Continue to Compass.
This standard has been approved for use by agencies of the Department of Defense. Or the D Table 1 data can be used to explain how the classification designation code for composite fiberglass piping is derived. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed dd2310 Two methods of classifying long-term strength are included: The inside diameter of the pipe is determined by the amount of material introduced into the mold.
There are two designation code generators look up scripts using the ASTM D standard classification. Last satm edition D — Pipe meeting this classi?
Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Formerly under the jurisdiction of Committee D20 on Plastics, this standard was withdrawn in August NOTE 5—Information regarding selection of service design factors and pressure rating is provided in Practice D and the individual product standards.
Therefore, it is possible to look up and ‘generate’ the ASTM D designation code or look up the property ‘by hand’.
Precedence for this change has been made in other ASTM standards. Benton, Ar Cell: Form Box Generator Site. B Refer to Practice D to obtain classification of the values. The manufacturer should be consulted. A superscript epsilon e indicates an editorial change since the last revision or reapproval.
Note 1 — For the purposes of this standard, polymer does not include natural polymers. A hydrostatic design basis as shown in Table 1 shall be determined for each type, grade, and class of product manufactured.
Changes in materials or manufacturing processes will necessitate a screening evaluation as described in Practice D A number in parentheses indicates the year of astj reapproval. The script was ‘debugged’ to the best of our ability! Standard categories for the hydrostatic design basis are shown in Table 1. NOTE 3—All possible pressure strength combinations of types, grades, and classes may not be commercially available. This cell-type format, however, is subject to misapplication since unobtainable property combinations can be selected if d210 user is not familiar with commercially available products.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is not based on dimensions or raw material specifications. The manufacturer should be consulted.