EKC 202D1 PDF

Buy B DANFOSS REFRIGERATION EKC D1, ller, I-pack the best price, fast worldwide shipping, up to 65% discount DANFOSS. EKC controllers can be used for a wide range of different refrigeration applications .. Regolatore per il controllo della temperatura – EKC D1, Literature. I need some help on this danfoss EKC D1. Its controlling a small freezer unit The set-point temperature is ยบ The R1 seting is diferential is.

Author: Shaktigal Zolojin
Country: Cuba
Language: English (Spanish)
Genre: Health and Food
Published (Last): 2 September 2016
Pages: 182
PDF File Size: 5.48 Mb
ePub File Size: 16.33 Mb
ISBN: 593-4-42597-512-8
Downloads: 52283
Price: Free* [*Free Regsitration Required]
Uploader: Nelmaran

Push the middle button again to conclude the setting. I need some help on this danfoss EKC D1.

EKC – Documents

A sensor before and after the evaporator: There will be change-over to the normal time delay A03 when the temperature has dropped below the set upper alarm limit. 22d1 change the controller from one freezer to another one, to rule out problems on the freezer, and the problem is in the controller.

Danfoss Group Global English U. Controller for temperature control – EKC D1. The actual defrost will be stopped based on time or temperature with a signal from a temperature sensor. A measurement of the defrost temperature can be obtained directly through the use of an S5 sensor or indirectly through the use 20d1 the S4 measurement.

Select the relevant number. To avoid a too low setting of the setpoint, the min. Delay on outputs during start-up 32 Other displays: Regolatore per il controllo della temperatura – EKC D1. Either with r12 or a DI-input 10 S Low alarm limit for S3 Here you must set the point at which the low temperature alarm is activated.

  EMINENCE DELTALITE II 2510 PDF

The signal to the thermostat, the alarm thermostat and the display can be set independently of one another. Icing-up will start a defrost. Universele koelregelaar – AK-CC manual. Refrigeration stopped by thermostat 11 S Regulator til temperaturstyring AK-CC manual. This forum is a free and open discussion board.

Controller for temperature control – EKC D1 Manual |

Go to career section Working at Danfoss. Uniwersalny sterownik urzadzenia chlodniczego, typu AK-CC Danfoss EKC D1 temperature settings. The running times are not observed when defrosts start. Controller tray for refrigeration appliance control with TEV. The value is the same as that set for the night increase value, but it is only raised if the value is positive. The next push restarts refrigeration The different situations can be followed on the display.

All the R codes: There are two kinds of error reports – it can either be an alarm occurring during the daily operation, or there may be a defect in the installation. Here are the messages that may appear: Electronic controller, EKC Programmable Controls Electronic Controls: The function will be active after each and every power failure.

Integration of V a. The relay cuts in when rail heat is to operate Light: The limit value is raised during night operation.

  2008 HONDA ACCORD COUPE MANUAL PDF

RS network card and battery back-up. Regolatore per il controllo della temperatura – EKC D1.

Continue session

If not, you can cancel the function with setting 0. Defrost is started at fixed time intervals, say, every eight hour Refrigeration time: If the function is controlled by a signal at the DI1 or DI2 input, the relevant status can be seen here in the menu. Data communication The controller is available in several versions where data communication can be carried out with one of the following systems: Push the upper or the lower button and select the new value 3.

Regulator til temperaturstyring – AK-CC manual. If the time is passed, a defrost will be started.

Select a negative value if there is to be cold accumulation. Minute setting t08 Clock: Standby position stopped refrigeration via r12 or DI input Standby mode A The limit value will also be raised in connection with reference ek r The thermostat 2022d1 are either placed in the cold air flow after the evaporator, in the warm air flow just before the evaporator, or both.

This display will appear for up to 15 minutes after cooling resumes.