FX1N HARDWARE MANUAL PDF

and wiring for Japanese specification FX1N PLC main units. This manual covers basic hardware details for the FX1N Series Programmable Logic Controller. FX1N Hardware Manual – 三菱可编程控制器FX1N型PLC硬件手册. User’s Manual. (Data Communication). FX1S/FX1N/FX2N(C)/FX3U. Interface Modules. INDUSTRIAL AUTOMATION. MITSUBISHI ELECTRIC. MITSUBISHI.

Author: Kigajin Voodoozil
Country: Burkina Faso
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 20 September 2014
Pages: 288
PDF File Size: 13.56 Mb
ePub File Size: 7.46 Mb
ISBN: 574-5-25415-686-8
Downloads: 61554
Price: Free* [*Free Regsitration Required]
Uploader: Akinolrajas

C M3 screw to secure top cover. Associated Manuals The following manuals are recomended as esential reference material for the correct operation of a FX1N series Programmable controller. The rated life for an inductive AC load such as a contactor or solenoid valve isoperations at 20VA. Parallel LED Eqn 1: If the current leakage is greater than the stated value, then add Rb. Only one board can manuxl used at any one time, do not try to stack multiple boards.

See fs1n 2 for Rb hadrware. C M3 screw to secure board. Screw terminals must be secured to prevent a loose connection from causing a malfunction. Take special care not to allow debris to fall inside the unit during installation e. If resistance Rp is less than the stated value, then add Rb. See equation 1 for Rb calculation. If a high speed response is required, a current of 10 – mA must be used.

  KLUBERSYNTH CTH 2-260 PDF

The FX1N does not have battery backup, if a system requires backup of more than 10 days, a peripheral backup power source must be provided. Never mount them to the floor or ceiling of an enclosure. To release, pull the spring loaded clips away from the rail and slide the unit up and off.

Owing to manuql very great variety in possible application of this equipment, you must satisfy yourself as to its suitability for your specific application.

Software warning 4 Indicates special care must be taken when using this element of software. These engineers should be fully aware of all aspects of safety with regards to automated equipment.

Once installation is complete remove the protective paper band, to prevent overheating. D, D M Program circuit error ref. AC, World spec, CE manuual. If a response time of 0. Note all counters are latched Remarks C0 to C15 Type: Verify the program to ensure it has been written to the PLC correctly. The enclosure should be selected and installed in accordance to the local and national standards. bardware

E M3 screw to secure top cover. Ground resistance must be less than ? This manual provides information for the installation and use of the FX1N.

Check the power LED is lit. Terminals screws should be tightened to between 0. D, D M Program execution error ref.

  EISENBAHN BAU UND BETRIEBSORDNUNG PDF

Mitsubishi FX1N-24MT-DSS Manuals

Do not remove this screw. Input circuit power supply? PL E xtension block? All maintenance should be carried out in accordance with established safety practices. The following instructions are also not hardqare. Down load a small test program into the PLC. AC Wor ld spec. Fix board to base unit using screws C. Terminal layouts The following selection of terminal layouts are taken from the FX1N product range.

Mitsubishi FX1NMT-DSS Manuals

Do not use this terminal Fuse Surge absorbing Diode. The capacitor backed memory will retain programs for a maximum of 10 days, and requires 30 minutes to recharge upon power up. This includes being completely haedware with all associated documentation for the said product. Please note that the over current induced by in-rush greatly reduces the relay contacts service life.

Each of the symbols used will now be listed with a brief description of its meaning. This manual is subject to change without notice. D, D M ref. Whenever any of the following symbols manial encountered, its associated note must be read and understood.