MANUAL HYLSA PDF

Read the instruction manual carefully before starting the pump. • These pumps may .. vid sådana tillfällen skyddas med någon form av hylsa. • Smörj samtliga. timely basis, you may not be able to vote by giving instructions to the depositary. Imsa transaction, to refinance existing indebtness of Grupo Imsa and Hylsa. Reporte Anual , Monterrey, Mexico: Hylsa. Oslo Manual: Guidelines for Collecting and Interpreting Technological Innovation Data, 3rd Edition, Paris.

Author: Najind Kira
Country: Pakistan
Language: English (Spanish)
Genre: Relationship
Published (Last): 5 April 2004
Pages: 497
PDF File Size: 7.10 Mb
ePub File Size: 1.82 Mb
ISBN: 304-3-52186-969-4
Downloads: 50664
Price: Free* [*Free Regsitration Required]
Uploader: Nejar

For that reason, the thermostats are sealed with enamel paint. Programme unit Al The steam valve is controlled by the programme unit A1. Install the new capillary tube in the same way as the old one. Press manula pulley onto the shaft.

Fit the new motor without locking the mounting bolts. The use of proper service tools and techniques, and the use of proper repair procedures, is essential to the safety of service personnel and equipment users. If the coin meter only have slot for one coin, all switches shall be placed in OFF position.

The door lock on the machine is described in detail in section The input signal from X94 is compared with the signal from the rotation sensor B3 input X Then lock the retaining screw.

  ENLACE IONICO Y COVALENTE PDF

Arbetsmateriallista – Karcher HKS 100 User Manual

Coin-meter Programming the current price 3 Programming is carried out on the switch unit, where the switches correspond to values from 1 to 64 when they are set on position ON. A faulty level switch can not be repaired and should be replaced. The door should remain locked! The piston lifts the pressure plate against the drain valve rubber diaphragm, which in turn forms a seal against the outer drum, effectively closing the valve.

All requests for assistance must include the model, serial number and electrical characteristics as they appear on the machine identification plate. Pull the emergency opening arm to the side. Jumper J short program. Be sure that the rear edge is fitted into the element holder at the rear of the outer drum. This is not shown here. The following check is made prior to unlocking of the door: Adjust drive belt tension if values exceed those shown in the table.

JVC KD S9R User Manual GET0007 005A

Remove the rear cover. The cover cannot be removed unless the main power switch is turned to the 0 position.

Undo the bracket for the drain hose connector from the lower rear piece, then remove the rear cover. Do not tamper with controls.

JVC KW NT30E NT30[E] User Manual LVT A

Door and door lock Contents Description Instruction for pulley hylss replacing bearings Service Manual 5, Fig. The card has separate checks for empty drum and stopped drum. In order to be able to put the puller blocks under the bearing, push the rear gable a little.

  DIRETTIVA MIFID TESTO PDF

These substances giveoff vapours that could ignite or explode. Be sure to put it on horizontally so that the sealings don’t get damaged on hjlsa shaft. The thermostat sensor is located at the lowest point of the outer drum to the left of the heating element. This overload protector protects the motor during the start-up of the extraction.

Undo the hose clamp holding the valve rubber bellows against the sleeve coupling of the outer drum. Motor Repairs 5 Main power switch Repair work on the machine should only be done by hyllsa trained personnel. This will cause the slow-blow fuse to trigger.

Control unit Communication card Fig. Motor replacement Disassembly Fig. Regular maintenance 11 To keep your machine in proper working order, follow the preventive maintenance recommendations provided below. Heating Function 2 Electric heating Fig. Heating contactor K22 Fig.

Arbetsmateriallista | Karcher HKS User Manual | Page 83 /

This unit also holds eight connectors for external detergent supply. Tap carefully it down in the bearing housing. The following check is made by the A31 card prior to locking of the door: